You want to modify the routing metrics for routes learned from or distributed into RIP.
You can modify the RIP metrics for a list of routes learned through a particular interface with the offset-list configuration command:
Router2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router2(config)#access-list 22 permit 192.168.20.0 Router2(config)#router rip Router2(config-router)#offset-list 22 in 5 Serial0.1 Router2(config-router)#end Router2#
A similar command changes the metrics for a list of routes as they are sent out through a specified interface:
Router2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router2(config)#access-list 33 permit 192.168.30.0 Router2(config)#router rip Router2(config-router)#offset-list 33 out 10 Serial0.1 Router2(config-router)#end Router2#
The offset-list command is most useful when you need RIP to distinguish between the costs of different links. By default, RIP looks only at the number of hops to the destination. But sometimes the longer path is significantly faster. For example, you might have a primary link that uses a T1 to get to a router in another building, and an Ethernet segment to get from there to another router that connects to a server. It's obviously better to take this primary link rather than a backup 56Kbps circuit that happens to connect directly to the last-hop router.
Other routing protocols (such as OSPF) address this problem by assigning a cost to each link and adding up the costs to find the best path. But RIP has only a metric. So, if you want to ensure that one path is preferred over another shorter one, you have to modify the metrics.
Cisco routers give considerable flexibility in changing metrics by adding an offset. This allows you to change each route independently as it is received or sent. You can even affect routes according to which interface the router receives them through. Be extremely careful because you can only increase a metric, never decrease it, and the maximum metric value is only 16. When the metric reaches a value of 16, RIP considers the network to be unreachable.
Sometimes you want to ensure that a particular path is never used to reach a certain destination. In this case, you can apply an offset of 16, and the router will have to find a different path. The router will also allow you to apply an offset of 0, but this has no effect.
The show ip protocols command lists all of the offsets that are configured, including information about the access lists, interfaces, and the sizes of the offsets that will be applied:
Router2#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 25 seconds
Invalid after 180 seconds, hold down 0, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Outgoing routes in Serial0.1 will have 10 added to metric if on list 33
Incoming routes in Serial0.1 will have 5 added to metric if on list 22
Redistributing: rip
Default version control: send version 1, receive any version
Interface Send Recv Triggered RIP Key-chain
Ethernet0 1 1 2
Loopback0 1 1 2
Serial0.1 1 1 2
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
172.25.0.0
192.168.30.0
Routing Information Sources:
Gateway Distance Last Update
172.25.2.1 120 00:00:12
Distance: (default is 120)
Router2#
A debug trace shows the incoming and outgoing routes. Note that the trace always shows the metric values after applying the offset for both inbound and outbound updates:
Router2#debug ip rip RIP protocol debugging is on Aug 10 23:24:36: RIP: sending v1 update to 255.255.255.255 via Serial0.1 Aug 10 23:24:36: RIP: build update entries Aug 10 23:24:36: subnet 172.25.25.2 metric 1 Aug 10 23:24:36: network 192.168.30.0 metric 11 Aug 10 23:24:48: RIP: received v1 update from 172.25.2.1 on Serial0.1 Aug 10 23:24:48: 0.0.0.0 in 1 hops Aug 10 23:24:48: 172.22.0.0 in 1 hops Aug 10 23:24:48: 172.25.1.0 in 1 hops Aug 10 23:24:48: 192.168.20.0 in 7 hops Router2#
|
|
|
| Top |